YouMagine

Information Comments Technical Files Builds Add build

Comments

You need to be signed in before commenting.

juliusvla

almost 8 years

Very nice design, thank you

david1

almost 9 years

just3dprint : http://www.ebay.com/itm/3D-Printed-Labyrinth-Gift-Box-for-Holidays-Birthdays-or-special-occasions-/262146385584?hash=item3d092466b0:g:zj8AAOSwLzdWSVa-

trepisky

about 10 years

<p>After printing I discovered that the inner part would not fit into the outer part (too big). What am I doing wrong? I am a total newbie so please dont shoot me if this is a dumb question... Beautiful design!!!</p>

Laertes

about 10 years

I love this one! I have printed three so far :) I will post a picture tonight.

mutrax

over 10 years

Hey, I've been using this as a geocache ( <a target="_blank" rel="nofollow" href="http://www.geocaching.com/geocache/GC5CD0Y_het-labyrint">http://www.geocaching.com/geocache/GC5CD0Y_het-labyrint</a> ) for a few weeks, and due to the loose fit , the geocachers managed to wear the stud out of the outer shell. Is it possible to uplooad one with a more narow fit? (.3 or so between the cyninders, and a close fit stud). Or upload the source files?<div>I'm printing one now at 99% to fix it.<br></div>

Christian

over 10 years

this is so cruel. I love it.

S.Ki

over 10 years

Thanks mutrax. Your comment came a bit late for me. I printed one day after my comment. I printed the lid of the gift box with the standard settings and a shell/bottom and top thickness of 0.8 mm and 100% infill while printing 0.1mm layers with a speed of 50mm/s. The result was pretty good. The bottom of the gift box was printed with the same parameters (for shell thickness and infill etc.) but with a speed of 30 mm/s. The result was pretty good aswell and lid and bottom fit together pretty nicely. Thank you for your help though, even if it was a bit late haha.

mutrax

over 10 years

Standard cura settings will do fine... Just increase the fill andere maybe shell/bottom/top thickness.

S.Ki

over 10 years

I want to print this but I'm unsure about the parameters. Any help?!

FinalFrag

over 10 years

I printed this yesterday (will add a picture later). When the box is closed it doesn't quite click into the closed position (even though it's supposed to do that looking at the print). There is also quite some vertical play when the box is closed. So I'll have to add some kind of rubber ring to make it a friction fit. It's really a minor issue though, the design of this thing is fantastic. I printed my top part a bit too hot so the bevel is a bit messy, but nothing a piece of sandpaper can't fix. I noted down the solution before closing it, so I cannot comment on how hard it is to open. Guess my victim will have to find out :) Thank you for this design, it's not something you mock up in an evening!

mutrax

over 10 years

Hey, I'm planning to use this one for a geocache.... See https://www.youmagine.com/designs/geocache-holder-for-labyrinth-gift-box

UltiErik

over 10 years

One requirement is also the constant cross section of the filament. And a fine layer height will help with making the surface nice and smooth.

IRobertI

over 10 years

Don't forget that images can be deceptive. The images here on Youmagine are so small that it's difficult to see imperfections. But in general though it's often a matter of printing slow to get great results. The faster you print the worse the quality gets (simplified).

Blizz

over 10 years

How do you guys get your prints so nice? I have an UM2 and I've never gotten a finish like that. Is it "post processed"?

Jeroen van Zijp

over 10 years

This is awesome! Can't wait to print it.

IRobertI

almost 11 years

Yes, that is the intended size. But you can always scale it down if you want to.

jonaseymour

almost 11 years

Great idea. @Eric, that's huge, is it meant to be that big? I was envisaging something the width of a cash note.

Fred

about 11 years

I solved it, and I like it :)

IRobertI

about 11 years

"I didn't have enough time to solve it" I like the sound of that :D

UltiErik

about 11 years

Yes, I printed this!!! I didn't have enough time to solve it (got a new born baby at home) but I'm printing more of these soon!! It's a great gift to give! Here's the obligatory picture: <a href="https://www.dropbox.com/s/xao4e3jbwzvfr5g/Screenshot%202013-12-16%2015.56.52.png" target="" rel="">https://www.dropbox.com/s/xao4e3jbwzvfr5g/Screenshot%202013-12-16%2015.56.52.png</a>

theshort

about 11 years

Way cool. One of my favorite things i've printed so far. It took awhile to get it off once I got it on. Other than some banding i'm fighting on my printer, it printed great.

Labyrinth Gift Box

By IRobertI

Comments

License

Tags

IRobertI

YouMagine

Labyrinth Gift Box

By IRobertI

Add To Collection

Comments

License

Tags

IRobertI

YouMagine