Axial Capra - Wazowski - Front Grill Light Bar
By SBI Prints
90% goes to the Creator
(excluding payment processing fees)
$4.50
Information
Axial Capra - Wazowski - Front Grill Light Bar
By SBI Prints
at 2024-10-31
Introducing our first Axial Capra upgrade, the - “Wazowski” Front Grill Light Bar - this led bar replaces the stock grill and headlights with your choice of retina burning led strip. Our light bar will make sure your Capra lights up the trails at night and won’t get lost in any deep trail brush.
Needed to complete:Two M2 x 6mm screws and an LED strip. We recommended a strip using 5054 LED at 120 led per meter at 12v if you’re running a 3S in your Capra.
Material: Our “Wazowski” Front Grill Light Bar can be printed in either PLA Plus or PETG for a bit more strength.
General dimensions: 81mm x 20mm x 10mm (L/W/H)
Installation:
You’ll need a 1.5mm hex driver for this install. The “1.5mm” is used below the driver sizes.
Begin by removing the two 1.5mm screws that hold on your stock grill and headlights. Keep these screws as you’ll need them later. After you have the grill off the Axial Capra, trace the wires back to your receiver and unplug them. You won’t be able to use your receiver to power our led bar.
To assemble the led bar, start by sliding the led strip into the curved strip holder; slide it far enough so that you can easily bend the wire through the cut out so that the wire exits the rear of the strip holder.
Next, center up the led strip so that it is even within the holder. Carefully bend the wires as needed and slide the led strip holder into the grill. Secure the led bar with the included M2 x 6mm screws; being careful not to over-tighten and stripe out the plastic. You just need it to be hand tight.
Finally install the grill on to your Axial Capra using the stock hardware you removed earlier. Once installed connect the LED bar to your truck in your preferred method.
-
Don't have a printer and still looking for this light bar setup? Checkout my Etsy store - https://sbiprints.etsy.com/
Needed to complete:Two M2 x 6mm screws and an LED strip. We recommended a strip using 5054 LED at 120 led per meter at 12v if you’re running a 3S in your Capra.
Material: Our “Wazowski” Front Grill Light Bar can be printed in either PLA Plus or PETG for a bit more strength.
General dimensions: 81mm x 20mm x 10mm (L/W/H)
Installation:
You’ll need a 1.5mm hex driver for this install. The “1.5mm” is used below the driver sizes.
Begin by removing the two 1.5mm screws that hold on your stock grill and headlights. Keep these screws as you’ll need them later. After you have the grill off the Axial Capra, trace the wires back to your receiver and unplug them. You won’t be able to use your receiver to power our led bar.
To assemble the led bar, start by sliding the led strip into the curved strip holder; slide it far enough so that you can easily bend the wire through the cut out so that the wire exits the rear of the strip holder.
Next, center up the led strip so that it is even within the holder. Carefully bend the wires as needed and slide the led strip holder into the grill. Secure the led bar with the included M2 x 6mm screws; being careful not to over-tighten and stripe out the plastic. You just need it to be hand tight.
Finally install the grill on to your Axial Capra using the stock hardware you removed earlier. Once installed connect the LED bar to your truck in your preferred method.
-
Don't have a printer and still looking for this light bar setup? Checkout my Etsy store - https://sbiprints.etsy.com/
License
Tags
Related objects
18 objects
3 Followers
Joined 4 months ago
SBI Prints focuses on quality parts for many different RC brands including: Axial, Redcat, Traxxas and Vanquish
Free