This is a full custom build from AMPro Engineering based oh the amazing looks of the Tamiya Hornet. While a totally stand alone car, there are a lot of parts that are needed to complete the build. Please see the full parts list and bill of materials at the bottom of the page. Many parts are compatible with the Tamiya Hornet and we have reused a number of AMPro parts for this build. There is a complete build video based on the three attached ZIP files to simplify the process.

e432 - SuperFly 3, Part 1: Front Suspension
https://youtu.be/jO-JWGlAun8

e433 - SuperFly 3, Part 2: Main Chassis
https://youtu.be/Xk3G1zV8Tiw

434 - SuperFly 3, Part 3: Transmission, Rear Suspension, & Details
https://youtu.be/S5FvCQAdgLU

Part 1 Front End

045001-2R - 20mm offset Arm Right

045001-2L - 20mm offset Arm Left

045002-01 - Front Bumper w/Aux Light Mount

045026-0R - Upright Right

045026-0L - Upright Left

045015-01 - 16.75mm HSP Shock Eyelets

045015-03 - 12.75mm HSP Shock Eyelets

045028-01 - Main Chassis - SW d

045028-02 - Front Bulkhead

045028-04 - Arm Retainer

045028-05 - Shock Tower

045035-01 – Steering block

045035-A3 - Servo Mount Only

045035-B3 - Servo Post (print 2)

045035-04 - Steering Bar

045035-do – Steer arm d

045035-po – Steer arm p

045037-01 - Suspension Set (inc front and rear towers, rear bumper) - Not used

045041-A2 - Upright, Bump Steer Reducer (Needs Tamiya Upright doner)

1/16 Scale HSP Shock, 65mm Front

Servo Saver

K-Power DM0260 Servo

Part 2 Main Chassis

045010-11 – Stock Cage

045007-01 - Wing and Shock Mount

045005-01 - Battery Door Retainer

045006-02 - Hornet Logo Battery Door v2

045028-A6 - Driver side Panel, pipes

045028-B6 - Driver side Panel, no pipes

045028-C6 - Passenger Panel, pipes

045028-D6 - Passenger Panel, no pipes

045028-E6 - Nose Panel

045028-07 – Side pipes

045028-08 - Belly Pan

045039-01 - Nerf Bars - SW

045044-01 - Front Body Mount

Part 3 Transmission & Details

045018-s0 - Omega Rear Arm

045029-01 - Right trans Case - SW

045029-02 - Left Trans Case - SW

045030-L2 - Left Upright, 1.5deg

045030-R2 - Right Upright, 1.5deg

045031-S1 - Rear Wheel One Piece Hornet, Single

045032-01 - Rear Tower

045032-02 - Rear Bumper - SW

045032-03 - Taillight Lens

045034-01 - Rear Skid Plate

045036-01 - Velocity Stack Base (steering wheel) - SW

045036-02 - Velocity Stack

045036-03 – Dash panel

045036-03 - Horn

045040-01 - B2 Motor Cover

045045-01 - B3 Oil Filler Cap

Roll Pins for CVD Axles (if not included in axle set)

Hex Drive for CVD Axles

Universal Joint for DF03RA/TA04 (Used Yeah Racing DF03RA-015BK)

1/16 Scale HSP Shock, 75mm Rear

RC Joint Cups, Tamiya Part Number: 9804181 (Comes in 2 and 4 pieces, 2 needed)

Tamiya Spring Mounts (used on stock hornet front lower shock mount, on arm)

Only Factory Pinion will work

Full Hardware BOM:

Self Tapping Screws

1 x 3mm, 6mm Long

12 x 3mm, 8mm long

40 x 3mm, 12mm long

2 x 3mm, 14mm long

Machine Screws

4 x M2.5 x 14mm

2 x M3 x 6mm Flat head (counter sink)

6 x M3 x 15mm

1 x M3 x 20mm

2 x M3 x 27mm

2 x M3 x 32mm

Screw Pins:

4x 3mm Shaft x 22mm

2x 3mm Shaft x 32mm (add 2 if you use a screw pin in the front suspension arm to hub)

Nuts:

4 x M2.5

4 x M3

10 x M3 Locknut

Washer

14 x 3mm ID

Ball Stud:

14 x M3 Shaft (if used with AMPro upright, 12 if not)

2 x M2 Shaft (if used with Tamiya upright, ignore if not)

Ball Cup:

14 x 3mm thread

Ball Bearings:

6 x 5x8x2.5

12 x 5x11

Brass Sleeves:

4x 3mm ID, 4mm OD, 6mm long